AirStage UTY-RNKG Installation Manual Download Page 3

En-2

CAUTION

Do not set the DIP switch of this unit except as speci

fi

 ed in this manual 

or the operating manual supplied with the air conditioner. Setting the 
switches other than speci

fi

 ed will cause an accident or trouble.

Use an insulated screwdriver to set the DIP switches.

Before opening the case of this unit, completely discharge static electricity 
charged on you body. Not doing so will cause trouble.

Do not touch the PC board and PC board parts directly with your hands. 
Otherwise, injury or electric shock could result.

Tightening the mounting screws too tight will damage the case of this unit.

Be careful so that the front case does not fall after the front case screws 
are removed. Otherwise, injuly could result.

Install the remote controller cables 1 m away from television and radio to 
avoid distorted images and noise.

Make sure water and insects do not enter the unit. Use putty, etc., as a 
countermeasure to gaps that may provide a route of ingress. Water and 
insects may cause malfunction, electric shock, or 

fi

 re.

Con

fi

 rm the name of each terminal block of the unit and connect the 

wiring in accordance with the directions given in the manual so that there 
is no incorrect wiring. Improper wiring work will damage the electric parts 
and cause smoke and 

fi

 re.

Perform wiring so that water does not enter this unit along the external 
wiring. Always install a trap to the wiring or take other countermeasures. 
Otherwise it will cause trouble or electric shock or 

fi

 re.

5.1.  Installation

Open the operation panel on the front of the remote controller, remove the 
2 screws indicated in the following 

fi

 gure, and then remove the front case of 

the remote controller.

When open the remote controller, remove the connector from the front 
case. The cables may break if the connector is not removed and the 
front case hangs down.
When installing the front case, connect the connector to the front case. 
When removing and connecting the connector, be careful not to break 
the cables.

Rear case

Front case (back side)

Connector

Screws

CAUTION

Be careful to avoid breaking the cable by over-tightening the cable tie. 

When connecting the remote controller cables, do not overtighten the 
screws.

(1)  Pass the remote controller cable through the hole in the rear case and 

connect the remote controller cable to the remote controller terminal 
block speci

fi

 ed in Fig.1.

(2)  Clamp the remote controller cable sheath with the cable tie as shown in 

Fig. 1.

Fig. 1

7

7

7

3. COM (Black)

2. Signal (White) 

1. 12V (Red)

Unit : mm

4.2.  Name of parts

With cover open

 

Display panel

1

2

3
4

5

6
7

F

G

H

E

8

9
0

A
B

C
D

1

 “ 

 ”,  “ 

 ” (Set Temperature Button)

2

 “ 

 ”  (Timer Mode/Clock Adjust Button)

3

 “ 

 ”  (Day/Day OFF Button)

4

 “ 

 ”  (Set Back Button)

5

 “ 

 ”,  “ 

 ”  (Set Time Button)

6

 “ 

 ”  (Timer Delete Button)

7

 “ 

 ”  (Timer Set Button)

8

 “ 

 ”  (Start/Stop Button)

9

 “ 

 ”  (Mode Button)

0

 “ 

 ”  (Fan Control Button)

A

 “ 

 ”  (Horizontal air

fl

 ow direction and swing Button)

B

 “ 

 ”  (Vertical air

fl

 ow direction and swing Button)

C

  “ 

 ” (Economy/Thermo Sensor Button)

D

 “ 

 ”  (Maintenance/Filter Reset Button)

E

 Operation Indicator

F

  Operation Lock Indicator

G

 Temperature Indicator

H

  Operation Mode Indicator

5.  INSTALLING THE REMOTE CONTROLLER

WARNING

Always use the accessories and speci

fi

 ed installation work parts. Not 

using the speci

fi

 ed parts will cause units to fall off, electric shock, 

fi

 re, etc.

Install at a place that can withstand the weight of the unit and install 
positively so that the unit will not topple or fall.

During installation work, do not permit children or users to approach. It will 
cause injury or electric shock.

Before starting installation work, turn off the power of indoor unit power 
supply. Do not turn on the power again until installation is completed. 
Otherwise, it will cause electric shock or 

fi

 re.

Use the attached cable. If extending or branching, implement suitable 
measures. When connecting the cables to the terminal, make sure to 
connect securely. Improper installation work may cause electric shock, 

fi

 re, or heat.

Install the remote controller cables securely to the terminal block. Con

fi

 rm 

that external force is not applied to the cable.
If intermediate connection or insertion 

fi

 xing are imperfect, it will cause 

electric shock, or 

fi

 re, etc.

Perform functional earthing work positively. Do not connect the functional 
earthing wire to a telephone functional earthing wire, water pipe, or 
conductor rod.

Always fasten the outside covering of the connection cable with the cable 
tie. (If the insulator is loose, short circuit may occur.)

9373328070-08_IM.indb   Sec1:2

9373328070-08_IM.indb   Sec1:2

8/17/2012   1:49:35 PM

8/17/2012   1:49:35 PM

Summary of Contents for UTY-RNKG









Reviews: