Airrex AHSC-18 User Manual Download Page 4

4

SAFETY NOTICE

GENERAL ADVICE BEFORE USE

·Ensure the safety of the location in which Heat Pump is to be used.
·Ensure the floor or ground is smooth and sound.
·Ensure you allow at least 20inch air space all around the Heat Pump.
·When in position LOCK the casters to prevent rolling.
·Never use the Heat Pump at more than 2。incline.
·If you use condensate pump, connect with housing in the power box.(Electric panel)

FOR MAXIMUM EFFICIENCY

·In airtight areas use vertical exhaust into ceiling.
·If possible locate exhaust outlet through a window or door to outside.
·Exhaust ducting should be no longer than 6.6 ft. for maximum efficiency.
·Ensure correct electricity supply.

CAUTION

Do not place Heat Pump on uneven, unstable or inclined surface.
(This could cause malfunction)

When storing the Heat Pump, ensure that it is kept in a dry, cool place.
(To prevent corrosion and malfunction)

If not being used for some time or if lightening is present, always unplug 
from power. (To prevent risk of electric shock, short circuit or fire)

Do not spray water on to the Heat Pump nor use solvents such as benzene, 
thinner or alcohol for cleaning.
(There is a risk of electric shock and / or short circuit)

Designed for indoor usage.

Summary of Contents for AHSC-18





















Reviews: