AirLive G.DUO User Manual Download | Manualshive

Page: 66 / 139

background image

6. AP Mode

57

AirLive G.DUO User’s Manual

6.2.5 Signal Survey

Operation Mode -> Setup -> Site Survey -> Signal Survey

The Signal Survey will continuously display the SIGNAL STRENGTH value of the selected
SSID for antenna alignment purpose. To use Signal Survey function, please enter the
“Site Survey” function first; please refer to the instruction in the above section. Once you
select the ESSID and click on the “Signal Survey” button, the following screen will appear.

BSSID

: This is the remote AP’s MAC address.

Channel

: The current scanned channel

Signal Strength

: This is signal strength number in percentage in 0 to 100 scale.

The higher the number, the better signal.

6.2.6 Enable MAC Clone (Single Ethernet Client)

When this function is enabled, G.DUO will replace the MAC address of Radio1 with the
first PC’s MAC address caught from the LAN port. It will allow one single Ethernet
client only. Please use this function only if you want to limit the Ethernet client to only
one.

«
...
64
65
66
67
68
...
»

Summary of Contents for G.DUO












































































































































Reviews:

No comments

Related manuals for G.DUO

Brand: SAGEMCOM Pages: 2

3CRWX385075A - Wireless LAN Managed Access Point...

Brand: 3Com Pages: 4

Brand: Mustek Pages: 67

Brand: M Box Pages: 60

Brand: ICP DAS USA Pages: 61

Brand: TP-Link Pages: 86

Brand: Zte Pages: 29

Juplink RX4-1500

Brand: Vanin Pages: 2

Brand: Grandstream Networks Pages: 29

Brand: EnGenius Pages: 6

Brand: EnGenius Pages: 60

Brand: EnGenius Pages: 62

Brand: EnGenius Pages: 76

Brand: EnGenius Pages: 89

Brand: Ericsson Pages: 12

Wi-REACH Classic

Brand: Connect One Pages: 38

Brand: Comcast Pages: 51

Brand: HPE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands