background image

33 

After you clicked Apply, the following message will be displayed on your web browser:  
 

 

 
You can click “Continue” to back to previous setup page to continue on other setup procedures, 
or click “Apply” to reboot the router so the settings will take effect (Please wait for about 30 
seconds while router is rebooting).  
 

3.1.4 DNS 

 

If you select 

Dynamic IP

 or 

PPPoE

 as Internet connection method, at least one DNS server’s 

IP address should be assigned automatically. However, if you have preferred DNS server, or 
your service provider didn’t assign the IP address of DNS server because of any reason, you 
can input the IP address of DNS server here. 

 

 

 

Parameter 

      

 

 

Description 

 
Primary DNS

 

Please input the IP address of DNS server provided by your 
service provider.  

 

Secondary DNS

 

Please input the IP address of another DNS server provided by 
your service provider, this is optional. 

 
 

After you finish with all settings, please click “Apply” button. 
If you want to reset all settings in this page, please click “Cancel” button. 
 

After you clicked Apply, the following message will be displayed on your web browser:  

 

Summary of Contents for AR660W3G













































































Reviews: