manualshive.com logo in svg

AIRLESSCO 25M232, Operation - Repair - Parts, Page: 23 / 72

Share
Download
AIRLESSCO 25M232 Operation - Repair - Parts Download Page 23

Flushing Recommendations

3A4637A Operation, Repair, Parts

23

Flushing Recommendations

If you are going to:

Flush with:

Prime with:

Clean with:

Store with:

Spray with new sprayer or 

sprayer that has been stored

Compatible solvent such as 

water or mineral spirits

Compatible paint, 

such as water-base 

or oil-base

Compatible solvent such 

as water or mineral 

spirits

Mineral 

spirits

Spray water-base paint

Warm, soapy water, then 

clean water

Water-base paint

Warm, soapy water, 

then clean water

Mineral 

spirits

Spray oil-base paint

Mineral spirits

Oil-base paint

Mineral spirits

Mineral 

spirits

Change water-base to

oil-base paint

Warm, soapy water, then 

clean water

Mineral spirits

Mineral spirits

Mineral 

spirits

Change oil-base to 

water-base paint

Mineral spirits, soapy water, 

then clean water

Water-base paint

Warm, soapy water, 

then clean water

Mineral 

spirits

Change colors, same base Compatible solvent such as 

water or mineral spirits

Summary of Contents for 25M232









































































Reviews:

No comments