AirKing ESDQIO series Instructions And Operating Manual Download Page 2

INSTALLATION INSTRUCTIONS

CAUTION:

 

MAKE SURE POWER IS SWITCHED OFF AT 

SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Range Hood

1.  Unpack hood from the carton and confirm that all pieces are present. In addition to the 

range hood you should have:

 

 

2 - Aluminum Grease Filters

 

 

1 - 3-1/4"x 10" Damper

 

 

3 - Damper Mounting Screws

 

 

4 - #8 Mounting Screws

 

 

1 - GU24 Base, 26W Fluorescent Lamp

 

 

1 - Instruction/Safety Sheet      

NOTE:

 Some hoods may be shipped with a protective plastic adhered to the range hood. It is 

recommended to leave this in place during installation to protect the hood from scratching. 

Remove when the installation is complete.

2.  Lay the hood flat on a table so the underside is facing you. Use a piece of cardboard to 

avoid damaging the table or the hood.

3.  Remove the following items from the hood and place in a safe place until needed 

(Figure 1):

 

Grease filters:

 Pull on tabs to remove.

 

Bottom cover:

 Remove the 4 screws holding it in place.

 

Lamp cover:

 Squeeze in the sides. The cover is held in place by tension against the tabs 

on the hood.

 

Wire compartment cover:

 Remove the screw holding it in place.

 

Blower:

 Using a 3/8" nut driver or ratchet, remove the 4 nuts holding the blower in place.

SECTION 2

Prepare the location for Hood Support

1.  If the hood will be installed under cabinets that have a recessed bottom, it will be 

necessary to install wood mounting strips (not included) so the hood will mount properly 

(Figure 2).

www.airkinglimited.com

5084457 Rev. P 1-16

2 of 12

2.  The thickness of the strips should be the same as the recess of the cabinet and they 

should be approximately 2" wide.

3.  Install the strips using appropriate length wood screws (not included). Make sure the 

strips line up to the keyhole slots of the range hood.

SECTION 3

Prepare the Hood for Installation

1.  Choose the type of ducting you will require. To ensure the best air and sound 

performance, it is recommended that the length of ducting and the number of elbows be 

kept to a minimum, the radius of each elbow be as large as possible for the installation, 

and that hard ducting be used. Larger duct sizes will reduce noise and airflow 

restrictions. This model is equipped to vent either Vertically or Horizontally through a 

3-1/4" x 10" duct. It can be modified to be ductless (re-circulates the air back into the 

kitchen) with the addition of 2 models CF-01 Charcoal Filters (not included) 

(Figure 3).

2a. 

Horizontal or Vertical

 - Remove the apprpriate square knockout by inserting a screw driver 

under the edge and break the tabs holding it in place. Peel back with pliers 

(Figure 4).

2b. 

Ductless

 - Lift up and remove the hood’s vent insert located behind the grill, exposing 

the front air slots. Do not use a screwdriver or any other object that could scratch the 

hood 

(Figure 4).

3.  Determine where the electrical service will enter the hood and remove the appropriate 

electrical knockout by inserting a screw driver into the slot and rocking back and forth 

until the knockout comes loose 

(Figure 4).

4.  Once the proper knockout(s) have been removed, either hold the hood up to the 

installation location and mark the locations of the ducting, electrical, and mounting holes 

or mark the locations by measurement.

5.  Cut appropriate holes for ducting connection and electrical connection in the wall/cabinet.

6.  For 3-1/4" x 10" vertical or horizontal ducting, install the damper assembly to the hood 

by sliding the tabbed section of the damper under the hood body and securing with the 

two provided screws. Using approved duct tape, tape around the collar to seal off any air 

leaks 

(Figure 5).

7.  Install an approved wire connector to the electrical knockout of the hood and guide the 

electrical cable through the hood, allowing at least 6" of wire for connections and tighten.

Figure 2

Wood Strip

Figure 3

Vertical

Ductless

Horizontal

Figure 4

Vertical

Ductless

Horizontal

Figure 1

Lamp Cover

Motor

Bottom

Cover

Wire

Compartment

Cover

Grease 

Filter Tab

Damper

Hood

Body

Tab

Figure 5

www.goedekers.com

Summary of Contents for ESDQIO series













Reviews: