background image

12

DV51  DV51CH

CAUTION

The minimum clearance 

between the bottom 

edge of the cooker 

hood and an electric 

stove is 426 mm .

INST

ALLA

TION

INSTALLATION OF THE COOKER 

HOOD 

The cooker hood is installed on the bottom of Adroit DV51CH .

1 .  Remove the plug from the feedthrough seal of the 

condensing water tube of the cooker hood (Figure 1) .

2 . 

Lift the cooker hood and fit the hooks at the rear of the 

cooker hood into the holes at the bottom of the ventilation 

unit . Push in place (Figure 2) .

3 .  Ensure that the feedthrough seal of the condensing water 

tube sits firmly around the tube.

4 . 

Lift the front of the cooker hood to fit the mountings into the 

penetrations in the bottom of the ventilation unit (Figure 3) .

5 .  Fasten the M5 hexagon screws (2) through the mountings 

(Figure 4) .

Lead the power cord and the control cable up along the 

cable channel (Figure 3) . Wind approx . half a metre of the 

cables behind the cooker hood so that it can be removed for 

maintenance purposes where required . Move the metal cover 

backwards so that it covers the opening between the cooker hood 

and the wall (Figure 5) .

1

2

3

4

5

Summary of Contents for Adroit DV51

































Reviews: