background image

PAGE: 5 / 9

Installation Steps :

Fig.1

Turn OFF the electric circuit at the

main fuse or circuit breaker box. 

Lock Pin

Hang the fan on Hanger Bracket, and 

make sure the slot of hanger ball is 

snapped into the chip of Hanger 

Bracket exactly.

Note: For slope ceiling installation, 

make sure the slot of hanger ball and 

the chip of hanger bracket face down.

Insert and tighten the two Collar 

Screws. Slide Lock Pin into Hanger

Pin until it is locked into position.   

Fig.6

Collar Screws

Fig.7

Slot

Chip

Hanger Bracket

NOTE: The fan weight is 17.28 lbs (7.84 kgs). Be sure the outlet box you are using is securely attached to the building 

structure and can support the full weight of the fan. Failing to do so can result in serious injury. 

INSTALLATION INSTRUCTIONS

IMPORTANT:

  BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION ON THE SEPARATE

  SHEET "SAFETY INSTRUCTIONS" AS WELL AS THE FOLLOWING "INSTALLATION INSTRUCTIONS". IF IN

  DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

  SAVE ALL INSTRUCTIONS. 

Collar

Collar

Hanger Pin

Fig.4

Motor Wires

Downrod

Downrod Stand

Cover 

Canopy

Downrod

Canopy

Downrod Stand

Cover 

Fig.5

Decorative Cap

Decorative Cap

Thread the motor wires through the 

downrod stand cover, decorative

cap, canopy and downrod.

Remove the Lock Pin and take off 

the Hanger Pin.  

Loosen the collar screws in part way.

Insert the Downrod into the Collar.

Slide Hanger Pin through holes of

Collar and Downrod. 

Hanger Pin

Lock Pin

Fig.3

 

Tighten the hanger bracket to the outlet box with two mounting screws.(

Make sure 

the outlet box is securely installed so that it will be able to support at least the 

fan weight.

)  Attach the safety cable hook to the ceiling with the dry wall screw and 

washer, and make sure the safety cable hook is covered by the fan canopy.

WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED "ACCEPTABLE FOR 

FAN SUPPORT"!

Fig.5.

Fig.2.

Ceiling

Hanger Bracket

Ceiling Joist

Wood Member

(2" x 4" Approx.)

Junction Box

Washer

Safety Cable Hook

Dry Wall Screw

Ceiling

Hanger Bracket

Ceiling Joist

Wood Member

(2" x 4" Approx.)

Junction Box

181128

Summary of Contents for F0048










Reviews: