www.airbasemakeup.com
Airbase Make-Up, 72a Windsor Street, Beeston, Nottingham, UK, NG9 2BW
twitter.com/AirbaseMakeUp facebook.com/AirbaseMakeUp
Trouble Shooting
Should your HD Home Use Airbrush System not be
spraying as you require, here are some solutions
to help you.
No Product Flow
1. Check that the needle is correctly inserted in to
the airbrush. Remove the back of the airbrush,
loosen the locking nut and pull the needle back.
Reinsert gently in to the airbrush so that the needle
is just visible from the front of the airbrush. Tighten the
locking nut and replace the back of the airbrush.
2. If the airbrush still does not spray, dismantle the
airbrush and perform a deep cleanse as directed
opposite.
Spitting Product
1. Remove the needle and nozzle cap at the front
(spraying end of the airbrush). Check that the cone
shaped nozzle is not damaged in any way. If it is
fractured this can cause spitting and you will need
to replace the nozzle for optimum performance.
2. Check that the needle is correctly inserted in to
the airbrush. Remove the back of the airbrush,
loosen the locking nut and pull the needle back
Reinsert gently in to the airbrush so that the needle
is just visible from the front of the airbrush. Tighten the
locking nut and replace the back of the airbrush.
3. If the airbrush continues to 'spit' spray just water
through. If the flow is even then thick foundation is
the issue. Thin the foundation when in the airbrush
cup with a little (2-3 drops) Airbase Thinner and
Cleaner.
No Air Flow
1. Remove the needle and nozzle cap at the front
(spraying end of the airbrush). Check that the cone
shaped nozzle is not damaged in anyway. If it is
damaged, causing closure of the small hole the
needle protrudes through this can cause loss of air
flow and you will need to replace the nozzle.
2. Check the socket that the unit is plugged in to has
power AND IS SWITCHED ON.
3. Check the airbrush hose is securely fitted to the
airbrush.
Deep Cleanse of your Airbrush
See our online guide.
1. Gently unscrew and remove the back of the airbrush.
2. Loosen the locking nut and remove the needle.
3. Unscrew and remove the spring case and split pin,
needle guide, trigger and saddle.
4. Unscrew the nozzle cap and needle cap (from the
front on the brush).
5. Clean all parts using Airbase Thinner and Cleaner
and a soft brush or disposable mascara wand.
6. Dry using a paper towel or soft cloth and rebuild.
7. Reassemble your airbrush making sure the locking
nut is tightly screwed.
ONLY if the nozzle becomes damaged should it be
removed using the wrench provided. Replace and
re-tighten ensuring you do not cross thread the nozzle.
WARNING! Do not over tighten
this will cause the
nozzle to sheer off from the body of the airbrush.
When cleaning, undo the back of the airbrush and pull
back the needle trigger so that the needle is no longer
visible when you look in to the colour cup. This will
protect the needle from accidental damage.
ATTENTION
1. This HD Airbrush Make-up System is only for use with
Airbase Make-up.
2. Be sure that no items are sticking out of the unit
before closing. The pressure of these items as you close
the lid could break your mirror.
3. This is not a toy and is intended for use by adults only.
Use of the unit, including cleaning and maintenance
should not be undertaken by children. For adult use only.
4. For additional protection, the installation of a residual
current device (RCD) having a rated residual
operating current not exceeding 30mA is advisable in
the electrical circuit supplying the bathroom. Ask your
installer for advice.
5. The appliance is not to be used by persons with
reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have
been given supervision or instruction. Please refer to the
instructions provided.
Please retain this information for future reference.
