Air Techniques G9510A Installation And Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 40

background image

6.3

System requirements

The system requirements of the software being used to operate the device must always be met during
its operation.
If third-party software is being used to operate the device, compliance with its system requirements
must be assured.
The following additional system requirements must also be met:

Drive:

DVD ROM

Interface:

USB 2.0
USB 3.0

Total maximum
cable length:

USB: 5 m

Software:

VisionX from version 2.4.10 (order number: E7300)
DBSWIN from version 5.17 (order number: E7200A), VistaEasy, Image Bridge

For the system requirements of the computer systems, visit the download area at www.airtech-
niques.com (document no. E7201).

Installation

16

2121100020L29 2101V007

EN-

US

«
...
16
17
18
19
20
...
»

Summary of Contents for G9510A









































Reviews:

No comments

Related manuals for G9510A

Brand: Landoll Pages: 52

Brand: JBSYSTEMS Light Pages: 14

Brand: YardShape Pages: 50

Brand: Taylor Pages: 70

Brand: Raith Pages: 26

Brand: Kane Pages: 16

Brand: Ecco Pages: 2

Brand: Landoll Pages: 94

Brand: Radarcan Pages: 40

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Brand: Gaspardo Pages: 44

Brand: Ironton Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands