Air Quality Engineering M660 Owner'S Manual Download | Manualshive

Page: 14 / 15

background image

14

TROUBLE SHOOTING

WARNING!

The following instructions are intended for qualified service personnel only. Dangerous line
voltage circuits are exposed during this procedure. Disconnect the power before servicing the
unit.

Check the Fan Motor and Power Source

If the fan does not run when the switch is on check the voltage supplied to the motor.

If the correct line voltage is not measured, check back through the wiring to the power source.

If the motor does not turn with the correct voltage applied, check to see that the shaft is free to turn.

Replace the motor, if necessary.

If the fan is noisy when the unit is in operation check the fan.

WARNING: Disconnect power before continuing! Manually turn the fan to make sure there is no
rubbing or grinding

Check the Wheel Rotation

Turn on power just long enough to start wheel rotating.

Check rotation for agreement with rotation arrow. Wheels are shown with counterclockwise rotation from
inlet side. If the rotation differs from the picture check wiring.

«
...
12
13
14
15
»

Summary of Contents for M660
















Reviews:

No comments

Related manuals for M660

Brand: Kärcher Pages: 30

R32 Split Series

Brand: Daikin Pages: 28

Brand: Lakeland Pages: 24

PowerForce 6583 Series

Brand: Bissell Pages: 16

Brand: Kärcher Pages: 27

Brand: Airwell Pages: 7

Brand: Cleanmaxx Pages: 44

1PAMSH09-SZO-14.5

Brand: Perfect Aire Pages: 12

Brand: Vertiv Pages: 44

Brand: RIDGID Pages: 36

WD 5.800 ecologic

Brand: Kärcher Pages: 158

VZL-7071 SERIES

Brand: Vax Pages: 8

Silence Force Extreme RO 5823.11

Brand: Rowenta Pages: 80

Brand: iGenix Pages: 24

Brand: Seifert Pages: 21

Brand: SEVERIN Pages: 120

Brand: Levoit Pages: 20

Brand: Lennox EMEA Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands