background image

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. 

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions

should always be followed to reduce the risk of fire,

electric shock and injury to person, including the following:

SAVE THESE INSTRUCTIONS

 TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO 

PERSON, OBSERVE THE FOLLOWING: 

a)  Use this unit only in the manner intended by the manufacturer. If 

you have questions, contact the manufacturer.

b)  Before servicing or cleaning the unit, switch power off at service 

panel and lock the service disconnecting means to prevent 

power from being switched on accidentally. When the service 

disconnecting means cannot be locked, securely fasten a 

prominent warning device, such as a tag, to the service panel.

 TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO 

PERSON, OBSERVE THE FOLLOWING: 

a)  Installation work and electrical wiring must be done by qualified 

person(s) in accordance with all applicable codes and standards, 

including fire-related construction.

b)  Sufficient air is needed for proper combustion and exhausting 

of gases through the flue (chimney) of fuel burning equipment 

to prevent back drafting. Follow the heating equipment 

manufacturer’s guideline and safety standards such as those 

published by the National Fire Protection Association (NFPA) 

and the American Society for Heating, Refrigeration, and Air 

Conditioning Engineers (ASHRAE), and the local code authorities.

c)  When cutting or drilling into wall or ceiling, do not damage 

electrical wiring and other hidden utilities.

d)  Ducted fans must always be vented to the outdoors.

e)  If this unit is to be installed over a tub or shower, it must be 

marked as appropriate for the application and be connected to a 

GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

f)  This unit must be grounded.

g)  To avoid motor bearing damage and noisy and/or unbalanced 

impellers, keep drywall spray, construction dust, etc. off power unit.

h)  Suitable for use with electronic speed control device.

CAUTION:

 

FOR GENERAL VENTILATING USE ONLY. DO NOT 

USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND 

VAPORS.

WARNING:

 

DO NOT USE IN KITCHENS.

i)  Read all instructions before installing or using exhaust fan.

www.airkinglimited.com

6728039 Rev. B 3-13

1 of 12

Exhaust Fan

Models:  ES80D, ES130D, ES80DG, 
ES130DG, ES80DH, ES130DH, ES130D2

Summary of Contents for ES130D













Reviews: