4
T
EMPERTURE INCREASE ABOVE INCOMING WATER TEMPERATURE
Figure 3 Wiring Connections
Microprocessor limits temperature increase according to the
pre-selected
temperature
Figure 4 Potentiometer Connection
TROUBLE SHOOTING GUIDE:
Your Instant-Temp water heater has no internal user serviceable parts and should be retuned to the factory for repair or replacement.
Please contact factory for return authorization. If after following the Installation Instructions, your Instant-Temp does not heat water
in accordance with this literature, please check the following:
1.
Check flow rate –
Controlling flow rate is essential to insure proper temperature rise. All Standard Flow Models require. 1.0 GPM to
activate and shut off t 0.65 GPM. All Low Flow models require 0.5 GPM to activate.
2.
LED Indicator –
If front panel LED does not illuminate check A/C breaker.
3. Low
Power –
Make sure of your exact voltage by using a voltmeter. You should obtain your reading off the two outside terminals located
on the heater. Compare this reading against the voltage specified in the Installation Instructions. The center terminal is always the earth
ground.
4. Low
Voltage –
The percentage of reduction in voltage will result in a like reduction in temperature rise.
5.
Low Amperage Draw –
Check amperage draw using an Amperage probe. Please compare your results with the Installation Instruction
sheets (Table 1) to determine if the heater is operating correctly.
6.
Length of pipe
– Length of pipe run will affect the temperature at the faucet. The heater should be mounted no more than 12-18 inches
from the point of use.
7.
Check Shut-Off Valve –
Check shut-off valve and make sure valve is open 100% to allow full water pressure to heater. Models require a
minimum of 45 PSI. (Low pressure (LP) models require 20-45 PSI).
8.
Freezing
– Instant-Temp heaters must be drained and stored if in a location subject to freezing. Disconnect the inlet/outlet compression
fittings and blow air through one side to the heater to assist draining. Failure to completely remove water from the unit will result in
freezing and cracking.
9. Problems? –
Call our toll-free hot line (800) 447-4962 or (310) 534-2300.
Exclusive 12-Month Warranty
Your Instant-Temp water heater has been engineered and built to the highest quality standards and is backed by a full, factory
warranty. Every Instant-Temp water heater is guaranteed to be free from defects in material and workmanship for a period of one (1) year
from the date of purchase. The above warranty applies to original purchaser if unit is installed to Chronomite Laboratories, Inc.’s
Installation Instructions. Chronomite Laboratories, Inc. will repair or exchange parts at the factory at no cost. This warranty is limited to
repairing or replacing said products which prove to be defective upon factory inspection FOB Harbor City, CA.
Air Delights, Inc.
9974 SW Arctic Dr.
Beaverton, Or. 97005
Toll Free Technical Hotline: (800) 440-5556 Telephone: (503) 352-1201
Fax: (503) 643-8224
I-919-Rev.5 -03/05 www.airdelights.com
MODEL
VAC
0.5GPM
1.0 GPM
1.5 GPM
2.0GPM
E-30 208 41
°°°°
F 21
°°°°
F 14
°°°°
F 10
°°°°
F
E-30 220-240 41
°°°°
F 21
°°°°
F 14
°°°°
F 10
°°°°
F
E-30 277 41
°°°°
F 21
°°°°
F 14
°°°°
F 10
°°°°
F
E-46 208 63
°°°°
F 31
°°°°
F 21
°°°°
F 16
°°°°
F
E-46 220-240 63
°°°°
F
31ºF
21
°°°°
F 16
°°°°
F
E-46 277 63
°°°°
F 31
°°°°
F 21
°°°°
F 16
°°°°
F
E-60 208 82
°°°°
F 41
°°°°
F 27
°°°°
F 20
°°°°
F
E-60 220-240 82
°°°°
F 41
°°°°
F 27
°°°°
F 20
°°°°
F
E-60 277 82
°°°°
F 41
°°°°
F 27
°°°°
F 20
°°°°
F
E-70 208 95º
F
48
°°°°
F 32
°°°°
F 24
°°°°
F
E-70 220-240 95
°°°°
F
48ºF
32
°°°°
F 24
°°°°
F
E-70 277 95
°°°°
F 48
°°°°
F 32
°°°°
F 24
°°°°
F
E-80 208
109
°°°°
F 54
°°°°
F 36
°°°°
F 27
°°°°
F
E-80 220-240
109
°°°°
F 54
°°°°
F 36
°°°°
F 27
°°°°
F
E-80 277
109
°°°°
F 54
°°°°
F 36
°°°°
F 27
°°°°
F
E-90 220-240
122
°°°°
F 61
°°°°
F 41
°°°°
F 31
°°°°
F
E-90 277
122
°°°°
F 61
°°°°
F 41
°°°°
F 31
°°°°
F
