air avionics AIR Control Display 57 Pilot'S Manual Download

Page: 51 / 58

Configuration Menu Diagram

This menu diagram only shows the basic configuration parameters accessible to
the flight crew. For a complete menu diagram including all pin code protected
parameters, please consult the ACD-57 Installation Manual [1].

Configuration
Menu

DEVICE

ILLUM OVERRIDE

Illumination over-
ride page: Man-
ually overrides
illumination con-
figuration

INFO

DATABASES

DB EXPIRY:
Database expi-
ration date

DB VERSION:
Database version

SERIAL: Device
serial number

VER: Software ver-
sion

VID: Vendor iden-
tification/manufac-
turer

PID: Product iden-
tification

Configuration
Menu

ALTIMETER

UNITS

PRESSURE

INHG: inches mer-
cury

HPA: hectopascals
(equals millibars,
default)

ALTITUDE

FT: feet

M: meters (de-
fault)

Configuration
Menu

COM SYSTEM

INSTALLATION

COM system spe-
cific menu items.
Please consult
COM system doc-
umentation for
an overview on
available param-
eters and recom-
mended values

COM CONTROL

KNOB USE

VOLUME: If not
in a menu, rotary
knobs are used for
volume selection
(default)

CHANNEL: If not
in a menu, rotary
knobs are used for
channel selection

STATION NAMES:
Values ON or OFF.
Default: ON

CHANNEL SPAC-
ING

8.3kHz

25kHz

BOTH (default)

ACD-57

Pilot’s Manual

rev. 1.0

2017/01/19

Summary of Contents for AIR Control Display 57



























































Search results

Summary of Contents for AIR Control Display 57

Reviews:

Related manuals for AIR Control Display 57

Brands by name

Popular brands

air avionics AIR Control Display 57, Pilot'S Manual

Search results

Summary of Contents for AIR Control Display 57

Reviews:

Related manuals for AIR Control Display 57

Brands by name

Popular brands