2
SAFETY PRECAUTIONS
The exclamation point within an equilateral triangle
is intended to alert the user to presence of impor-
tant operating and maintenance (servicing) instruc-
tions in the literature accompanying the appliance.
SECURITE
Le point d'exclamation à l'intérieur d'un triangle
équilatéral avertit l'utilisateur de la présence d'in-
structions importantes d'utilisation et de mainte-
nance dans la documentation accompagnant l'ap-
pareil.
SICHERHEITSVORKENHRUNGEN
Das Ausrufezeichen in dem gleichseitigen Dreieck
ist dazu da, den Benutzer auf wich-tige
Inbetriebnahme- und Instandhaltungs-vorschriften
hinzuweisen, die dem Gerät in Form einer
Broschüre beigelegt sind.
PRECAUCIONES DE SEGURIDAD
El símbolo de exclamación dentro de un triángulo
equilátero, se muestra con el objetivo de alertar al
ususario de que instrucciones de operación y man-
tenimiento importantes acompañan al equipo.
1
UNPACKING
Unpack carefully.This is mechanical equipment and should be
handled with care.
Check for the following items:
•
Verify the unit model number.
•
Instructions for Use.
If an item appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper. If any items are
missing, notify Aigis Mechtronics.The shipping carton is the
safest container in which the unit may be transported. Save it
for possible future use.
2
SERVICE
If the unit ever needs repair service, the customer should
contact Aigis Mechtronics.
3
DESCRIPTION
MT9208SS 20-cm (8-in) Mount
MT9212SS 30-cm (12-in) Mount
MT9215SS 38-cm (15-in) Mount
These indoor/outdoor mounts are designed for camera
housing installations up to 11.3 kg (25 lb) rated load for the
MT9208SS and the MT9212SS and 22.68kg (50 lbs) for the
MT9215SS.These models are made of Stainless Steel and
feature welded construction, providing an extremely rigid
camera mount.These mounts have been designed specifically
for the HS9383S series housings. All mounts come fully
assembled.
4
INSTALLATION
1. Determine a secure wall mounting location.
2.
Cautions:
a.
For a secure installation, use four 8-mm (5/16-in)
diameter fasteners (not included). Use stainless steel
fasteners.
b.
If bolts are used, they should extend through the
mounting surface and be secured with flat washers,
lock washers, and nuts on the opposite side. Each
bolt must have a minimum pull-out strength of 200
kg (450 lb).
c.
If studs are used, they should be anchored in
concrete or welded to a steel backer plate. Each
stud must have a minimum pull out strength of 200
kg (450 lb).
d.
If the wall mount is attached to wood or to a blind
structure (with no access to the rear), each fastener
must have a minimum pull-out strength of at least
200 kg (450 lb).
3. Locate the four holes or stud locations using the flange as
a template (four holes equally spaced on a 69.9-mm (2-
3/4-in bolt circle).
4. Feed wires through the large hole in the flange where the
camera housing mounts.
5. Install the mount using bolts or studs at least 8-mm (5/16-
in) in diameter.
6. To mount the camera housing:
a.
Remove the 4 screws and washers from the head of
the mount. See
Figure 1.
b.
Attach the housing to the mount by aligning the
holes in the foot of the housing with the 4 holes in
the mount. See
Figure 2
.
c.
Reinstall the screws and the washers.
d.
Lock the mount head in position by using the
supplied 1/8-inch long-arm hex wrench to tighten
screws.
