Aigis Mechtronics HS9383S-2HP Installation And Operating Instructions Manual Download Page 3

This label may appear on the bottom of the unit due to
space limitations.

The lightning flash with an arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons. 

The exclamation point within an equilateral
triangle is intended to alert the user to presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.

CAUTION: 

TO REDUCE THE RISK OF ELECTRICAL

SHOCK, DO NOT OPEN COVERS. NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.

3

SAFETY PRECAUTIONS

FCC & ICES INFORMATION

(U.S.A. and Canadian Models Only)

WARNING 

- This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Intentional or unintentional changes or modifications not expressly approved by the party responsible for
compliance shall not be made.   Any such changes or modifications could void the user's authority to operate the
equipment.

The user may find the following booklet prepared by the Federal Communications Commission helpful: "How to
Identify and Resolve Radio-TV Interference Problems". This booklet is available from the 
U.S. Government Printing Office, Washington, DC 20402, Stock 
No. 004-000-00345-4.

Summary of Contents for HS9383S-2HP













Reviews: