Sichuan AI-Link Technology Co., Ltd.
page
6 of 8
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
If power exceeds the limit and the distance
（
Over 20cm distance in actual use between the device and user
）
is
compliant with the requirement
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
Notice to OEM integrator
If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module.
The end product shall haves the words “Contains Transmitter Module FCC ID: 2AOKI-WFM38GUTH1”.
The device must be professionally installed
The intended use is generally not for the general public. It is generally for industry/commercial use.
The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is
not normally required. The user has no access to the connector.
Installation must be controlled. Installation requires special training
Any company of the host device which installs this modular with unlimited modular approval should perform the test of
radiated & conducted emission and spurious emission, etc. according to FCC part 15C: 15.247 and 15.209
& 15.207, 15B Class B requirement, only if the tests result comply with FCC part 15C: 15.247 and 15.209 &
15.207, 15B Class B requirement, then the host can be sole legally
When the module is installed inside another device, the user manual of the hose contain below warning statement:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
C
、
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
This product meets the applicable Industry Canada technical specifications.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation,
Sciences et Développement économique Canada. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
1)L'appareil ne doit pas produire de brouillage;
2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label referring to the enclosed
module. This exterior label can use wording such as the following: “Contains IC: 23460-WFM38GUTH1” any similar
wording that expresses the same meaning may be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des
mots «Contient un module d'émission », du mot « IC: 23460-WFM38GUTH1 » ou d'une formulation similaire
exprimant le même sens, comme suit
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with
