+
100V Line
When it is desired to connect speakers or driver units at a
distance over 50 meters, it is recommended that the 100V line
output be used together with line matching transformer for each
speaker. This prevents excessive power loss in the speaker
cables.
4
8
1
6
1
0
0
V
C
O
M
30W
20W
10W
5W
40W
COM
1
L1
L2
30W
20W
10W
5W
40W
COM
2
L1
L2
30W
20W
10W
5W
40W
COM
7
L1
L2
• Operating Procedure
PWR
MON
POWER
C-1
D
A
2V
C
TREBLE
BA S
S
E
EJ CT
F
F
PLAY
0
2
4
6
8
+10
2
0
2
4
6
8
+10
2
FULL REEL
EXPOSED TAPE
CASSETTE INSERTION
+
Hold the cassette tape in such a manner that the exposed
tape area is facing towards your right and the full reel of
tape is towards you.
+
Now insert the cassette into the cassette loading slot firmly
and push it in until it snaps into position.
+
To retrieve the cassette, push in the FF / EJECT lever fully
and the cassette will eject out.
AC MAINS OPERATION
Set all volume controls to '0' position and keep the power
switch at OFF position. Connect the speakers and required
inputs.
Plug in the AC power supply cord to the nearest AC mains
socket and put the power switch to POWER position. The pilot
LED should glow.
Adjust the volume and tone controls to the desired level in the
following manner:
1. With all the mic volume controls set at ‘0’ position, raise
MASTER volume control to 7 or 8 position.
2. The BASS and TREBLE controls should be set at ‘0’ (Flat)
position.
3. Move the volume control of MIC-1 slowly to the desired
sound level but not up to the point where howling and
feedback starts.
4. Now repeat the same for MIC-2, MIC-3 and so on.
5. When using a fourth microphone, use MIC-4 jack and
keep the MIC/TAPE selector switch at MIC position.
6. When using Aux as input use RCA jack provided at the
rear panel and keep MIC-3/AUX control at desired level.
7. Now use the MASTER control for raising or lowering the
overall volume level as desired.
8. When playing a tape, keep the MIC/TAPE switch at
TAPE position.
9. The tape can be advanced rapidly by pushing in the FF /
EJECT lever partially.
10. To stop the tape, push in the FF / EJECT lever fully so that
the cassette is ejected out.
11. Due to the Auto Stop system, the cassette is
automatically stopped when the tape comes to an end in
play mode.
12. The Bass and Treble controls should be individually set to
the desired level as explained below:
BASS: This controls the tonal quality of low frequencies
produced by musical instruments like Tabla / Drum etc., and
to some extent male human voice. When this control is
advanced towards BOOST position, it will boost i.e. increase
the intensity of the low frequencies. Similarly, when it is
lowered towards CUT position, it will cut i.e. reduce the
intensity of low frequencies.
TREBLE: This controls the tonal quality of high frequencies
produced by musical instruments like Violin, Sarangi and
Sitar etc. and to some extent female human voice. When the
control is advanced towards BOOST position, it will boost i.e.
increase the intensity of high frequencies. Similarly, when
lowered, towards CUT position, it will cut i.e. reduce the
intensity of high frequencies.
���훍양蕁Ꝥ먠虂ﾻ랺뢶뒲���૨웹
���枓뾭魒畴殧㴼폊ޝ髥͏컭红鶼뜂苍짬㝖农뿣璘㠶䗫㫟
���⁌祧鎿癭̂颏蘜媠㛍쌊ꃌ윒嵙矂憬ꟲᚕ羽榴꾫컊엨܂乬譫ᄎퟕ퍸ḛ
���ြ짇따巄官輥氂頮ⷃ婋橥͏涸듗∞榴ퟶ䆌袃鶙껰ᐲ㼼㨸���
���鷉ြ뒫䇘쿅屓䫠瘌̀膠暨쳯ሎⱷ싡ⱐ䭇鋝���䊍���輵���縣℟쓂
���ြ⩗䑱
麕
뙍䏚ឭ脗굵焏㉑䶘똁ﷸ誆臌䳪൘ꏇⰧ⍮屬
���鷉鶛ଂ颗ⴤ懷쩠Ꚗ
훒邋긮免
띵飚╄捞緈፞꧈쎿먆兌쟔⌡쟄
���ြ⩗쿼쐋ɉ���헌扙龞
ః馐蟄그䍢괭䱇Ԁ
⇓ ϑ
⇓ °∧ι ψ
���࢈♉䫰ǿꖢꂞ䏩
���鯇嗢콝觃몱䜾㗌扙鼤
穱桟竆쇠⭶쇠⮪
���ฺ⠖䉀���륐雔쭡塏谢롏옑醯꯶䅤恾窼���☡氋
武넱籷ᙡ○죩
���乻榕셥ﯺ縔꫱蜝ᐋ轢û䝂㴹蓏㑓黩㑓鸞㰸菎ఇ錸���锻㣞
���鷉鶋峲癭擺邇ି뺹Ԁﯷ䊍覄콏宦쫅徂췉ᐏଆ农飱䃦ܙ뻾
���乻楗莯鵥ﭿᔔଂ頮├늩뙴澓똁
