background image

Specifications are subject to change without notice.

2

441 01 4200 01

SAFETY CONSIDERATIONS

FIRE, EXPLOSION, ELECTRICAL SHOCK, AND

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in dangerous

operation, serious injury, death, or property damage.
Improper installation, adjustment, alteration, service,

maintenance, or use could cause carbon monoxide

poisoning, explosion, fire, electrical shock, or other

conditions which may cause personal injury or property

damage. Consult a qualified service agency, local gas

supplier, or your distributor or branch for information or

assistance. The qualified service agency must use only

factory--authorized and listed kits or accessories when

modifying this product.

!

WARNING

FURNACE RELIABILITY HAZARD

Improper installation or misapplication of furnace may

require excessive servicing or cause premature component

failure.
Application of this furnace should be indoors with special

attention given to vent sizing and material, gas input rate,

air temperature rise, unit leveling, and unit sizing.

CAUTION

!

Improper

installation,

adjustment,

alteration,

service,

maintenance, or use can cause explosion, fire, electrical shock, or
other conditions which may cause death, personal injury, or

property damage. Consult a qualified installer, service agency, or
your distributor or branch for information or assistance. The

qualified installer or agency must use factory--authorized kits or

accessories when modifying this product. Refer to the individual
instructions packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,
and work gloves. Have a fire extinguisher available. Read these

instructions thoroughly and follow all warnings or cautions
include in literature and attached to the unit. Consult local

building codes, the current editions of the current edition of

National Fuel Gas Code (NFGC) NFPA 54/ANSI Z223.1 and the
current edition of National Electrical Code (NEC) NFPA 70.

Recognize safety information. This is the safety--alert symbol

.

When you see this symbol on the unit and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words

DANGER

,

WARNING

, and

CAUTION

. These words are used with the safety--alert symbol.

DANGER

identifies the most serious hazards which

will

result in

severe personal injury or death.

WARNING

signifies hazards

which

could

result in personal injury or death.

CAUTION

is

used to identify unsafe practices which

may

result in minor

personal injury or product and property damage.

NOTE

is used

to highlight suggestions which

will

result in enhanced

installation, reliability, or operation.

CUT HAZARD

Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care

and wear appropriate protective clothing, safety glasses and

gloves when handling parts and servicing furnaces.

CAUTION

!

1. Use only with type of gas approved for this furnace. Refer

to the furnace rating plate.

2. Install this furnace only in a location and position as

specified in the “Location” section of these instructions.

3. Provide adequate combustion and ventilation air to the

furnace space as specified in “Air for Combustion and

Ventilation” section.

4. Combustion products must be discharged outdoors.

Connect this furnace to an approved vent system only, as

specified in the “Venting” section of these instructions.

5. Never test for gas leaks with an open flame. Use a

commercially available soap solution made specifically for

the detection of leaks to check all connections, as specified

in the “Gas Piping” section.

6. Always install furnace to operate within the furnace’s

intended temperature--rise range with a duct system which

has an external static pressure within the allowable range,

as specified in the “Start--Up, Adjustments, and Safety

Check” section. See furnace rating plate.

7. When a furnace is installed so that supply ducts carry air

circulated by the furnace to areas outside the space

containing the furnace, the return air shall also be handled

by duct(s) sealed to the furnace casing and terminating

outside the space containing the furnace. See “Air Ducts”

section.

8. A gas--fired furnace for installation in a residential garage

must be installed as specified in the warning box in the

“Location” section (see Fig. 5).

9. The furnace is not permitted to be used for heating of

buildings under construction.

10. These Multipoise Gas--Fired Furnaces are CSA (formerly

A.G.A. and C.G.A). design--certified for use with natural

gas (see furnace rating plate) and for installation in

alcoves, attics, basements, closets, utility rooms,

crawlspaces, and garages. The furnace is factory--shipped

for use with natural gas and cannot be converted for use

with propane.

11. See Fig. 2 for required clearances to combustible

construction.

12. Maintain a 1--in. (25 mm) clearance from combustible

materials to supply air ductwork for a distance of 36

inches (914 mm) horizontally from the furnace. See

current edition of NFPA 90B or local code for further

requirements.

13. These furnaces SHALL NOT be installed directly on car-

peting, tile, or any other combustible material other than

wood flooring. In downflow installations, factory access-

ory floor base MUST be used when installed on combust-

ible materials and wood flooring. Special base is not re-

quired when this furnace is installed on manufacturer’s

approved coil assembly or a manufacturer’s coil casing

box is used. See Fig. 2 for clearance to combustible con-

struction.

INTRODUCTION

This 4--way multipoise Category I fan--assisted furnace is CSA

design--certified. A Category I fan--assisted furnace is an

appliance equipped with an integral mechanical means to either

draw or force products of combustion through the combustion

chamber and/or heat exchanger. The furnace is factory--shipped

for use with natural gas.

This furnace is not approved for installation in mobile homes,

recreational vehicles, or outdoors. The furnace is not permitted to

be used for heating of buildings under construction. This furnace

is designed for minimum continuous return--air temperature of

60

_

F (16

_

C)db or intermittent operation down to 55

_

F (13

_

C)

db such as when used with a night setback thermostat. Return--air

temperature must not exceed 80

_

F (27

_

C) db. Failure to follow

these return--air temperature limits may affect reliability of heat

exchangers, motors, and controls. (See Fig. 3).
For accessory installation details, refer to the applicable
instruction literature.

NOTE

: Remove all shipping brackets and materials before

operating the furnace.

Summary of Contents for F80CSU













































Reviews: