background image

24

INSTALLING THE CLEVIS PINS

STEP 58:  (REFER BACK TO FIGURE 54 ON PAGE 23)

•  Lift the front of the snow blower to align the holes in 

the mounting plates and the side plates. Insert two 
1/2" x 7/8" clevis pins through the holes and secure 
them with the 1/8" hairpin cotters.

SETTING THE AUGER BELT TENSION

STEP 59:  (SEE FIGURE 57)

•  Pull the tensioning chain until the end of the spring is 

pulled through the hole in the side of the Clutch/Idler 
assembly. Install a 1/8" hairpin cotter through the end 
of the spring, securing it on the outside of the Clutch/
Idler assembly.

IMPORTANT:

  For correct belt tension, 

the 1/8" hairpin

cotter must attach to the end of the spring

, not to the

chain.

NOTE;

  To prevent the chain from dragging on the

ground, loop the end of the chain though the pivot lock
pin. Refer to figure 56 on page 23.

FIGURE 57  

VIEWED FROM UNDERNEATH

REAR REFLECTORS

 

ATTACH REFLECTORS TO REAR FENDER

STEP 59:  (SEE FIGURE 58)

•  If your tractor is not equipped with rear reflectors, 

assemble the supplied rear reflectors to the rear 
fender. Place the reflectors as close to the bottom of 
the fender and as far apart as the shape of the fender 
will allow.

FIGURE  58

CHECKLIST

Before you operate your snow thrower, please review the 
following checklist to help ensure that you will obtain 
the best performance from your snow thrower.

1.  All assembly instructions have been completed with all 

bolts and nuts properly tightened.

2.  Check the engine belt and the auger belt. Make sure 

they are routed properly around pulleys and inside all 
belt keepers.

3.  Check discharge chute for proper rotation.

4.  Check operation of tilt control for upper chute.

5.  Verify that the lift handle will lock into and release from 

the raised transport position. (Refer to the Service and 
Adjustments section.)

6.  Check skid shoe adjustment. (Refer to the Service and 

Adjustments section.)

Operating instructions begin on page 25.

1/8" HAIRPIN COTTER

IDLER FLAT PULLER

AUGER BELT

RIGHT SIDE OF TRACTOR

Summary of Contents for LST42E





































Reviews: