AGP DM62 Original Instructions Manual Download Page 5

5

DRILL SAFETY WARNINGS

1.  Wear ear protectors when impact drilling. 

Exposure to noise can cause hearing loss. 

2.  Use auxiliary handle. 

Loss of control can cause personal injury.

3.  Hold power tool by insulated gripping surfaces, when performing an operation where the cutting 

accessory may contact hidden wiring or its own cord. 

Cutting accessory contacting a "live" wire may 

make exposed metal parts of the power tool "live" and could give the operator an electric shock.

4.  Check the ground (earth) connection of the electrical plug.
5.  Block off the working area and place warning signs on both sides of the wall  when drilling through 

from one side to the other.

INTRODUCTION

The machine is equipped with vertical and horizontal spirit levels  to aid in aligning when drilling.  
By positioning the machine so that the bubble is in the center of the window one can drill a straight hole. 
This machine is for the intended purpose of diamond core drilling of concrete, masonry, stone and similar 
materials. It may also be mounted on a rig (drilling stand).   
All other uses which are not for the intended purpose are prohibited.
It is equipped with a two speed gearbox.
All models are equipped with a mechanical safety clutch.
All models have electronics for soft start, overload protection, and thermal protection.

ELECTRICAL CONNECTION

The  network  voltage  must  conform  to  the  voltage  indicated  on  the  tool  name  plate. 
Under  no  circumstances  should  the  tool  be  used  when  the  power  supply  cable  is  damaged.  A  damaged  
cable  must  be  replaced  immediately  by  an  authorized  Customer  Service  Center.  Do  not  try  to  repair the 
damaged cable yourself. The use  of  damaged  power  cables  can  lead  to  an  electric shock.

Symbols used in this manual

V…….........volts
A…….........amperes
Hz…….......hertz
W……........watt
~………....alternating current

n

 

………...rated speed

min

-1

….......revolutions or reciprocation

  

per minute

.........warning of general danger

 .…..class II tool        

 .......read these instructions

......always wear eye protection

......always wear a dust mask.

 .....always wear hearing protection  

 .....wear safety-approved hard hat

  do not dispose of electric tools,     
  accessories and packaging together
   with household waste material

Summary of Contents for DM62

















Reviews: