manualshive.com logo in svg

Agora Models LONDON TRANSPORT ROUTEMASTER BUS, Build Instructions, Page: 27 / 50

Share
Download
Agora Models LONDON TRANSPORT ROUTEMASTER BUS Build Instructions Download Page 27

1

2

1

Fit the raised square section of the rocker lever 

36I

 into the opening in the gear box section 

36K

. Fit the square opening in the steering gear 

36H

 over the raised square section of 

36I

. Fix in 

place with a 

PM

 screw.

2

Take the steering shaft 

36G

 and fit it into the gear box 

section 

36K

. Ensure the ridges on part 

36G

 fit into the 

neck of part 

36K

, as indicated by the red dotted lines. The teeth 

on the end of part 

36G

 should connect with the teeth on part 

36H

. Fit the second gear box section 

36L

 so that the end of part 

36G

 is enclosed. Fix in place with three 

CM

 screws as shown.  

3

4

3

Fit the socket on the push rod 

36J

 over the peg 

on the end of part 

36I

. Fix in place with a 

QM

 

screw. Do not overtighten. 

4

Fit the hole in the end of the gear lever 

36C

 over 

the peg in the gear lever housing section of part 

36E

 as indicated by the blue dotted line. Fit the gear 

lever cover 

36D

 over the gear lever to hold it in place. 

Fix in place with a 

DP

 screw. 

PM

DP

CM 

x3

QM

36I

36K

36H

36K

36L

36G

36C

36I

36J

36D

36E

27

27

AGORA

MODELS

28

AGORA

MODELS

RM 857

Summary of Contents for LONDON TRANSPORT ROUTEMASTER BUS



















































Reviews:

No comments