background image

13

TriScroll 610 Dry Scroll Vacuum Pump 

TriScroll 600 Series 
Maintenance Manual

General Information

Agilent TriScroll 600 series pumps are designed to provide years of trouble-free service if maintenance procedures and
intervals  are  observed.  Cleaning,  bearing  grease  replenishment  and  tip  seal  replacement  is  recommended  when  pump
base pressure has risen to an unacceptably high level for your application. Bearings, rotary seals and o-rings should also
be replaced if the pump exhibits humming or grinding noises form the bearings. Main bearing life may be shortened if
your application requires the pumping of high quantities of water vapor. Use of the bearing purge described earlier will
keep this water from impacting bearing life.

Maintenance should be performed in accordance with procedures, tooling and materials specified in the manuals listed
below.

Related TriScroll Manuals

Other manuals related to the Installation and Operation, Tip Seal and Pump Module Replacement for TriScroll 600 series
pumps are listed in Table 5.

Maintenance and Tooling Kits

Material and tooling required to perform maintenance on TriScroll pumps is provided in kit form. A description of each kit
and ordering information is provided in Table 6.

Table 5

Related TriScroll Manuals

Part Number

Title

Applicable TriScroll Model

699904290

Installation and Operation Manual

All TriScroll 600 models

699904295

Installation and Operation Manual

All TriScroll 610 models

699904310

Tip Seal Replacement Manual

All TriScroll 600 and 610 models

699904300

Pump Module Replacement Manual

All TriScroll 600 and 610 models

699904305

Maintenance Manual

All TriScroll 600 and 610 models

699904300

Maintenance Manual

All TriScroll 600 and 610 models

Table 6

Maintenance and Troubleshooting Kits

Part Number

Description

Contents

Applicable TriScroll 

Model

PTSS0600MK

Maintenance Kit

All bearings, bearing 
seals, bearing 
lubricant, O-rings, and 
tip seals required to 
rebuild TriScroll 600 
series pumps.

All TriScroll 600 and

610 models

PTSS0600TK

Maintenance Tool Kit

All fixtures and tools 
required to perform 
any maintenance on 
TriScroll 300 series and 
TriScroll 600 series 
pumps.

All TriScroll 300, 310, 
600 and

610 models

Summary of Contents for TriScroll 610



























Reviews: