manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 76 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 76

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Troubleshooting
Troubleshooting the RF Path (N5161A/62A/81A/82A)

1-68

3.

Using 

Table 1-10

, re-check the maximum power levels.

— If the signal generator meets its maximum power levels, proceed to 

“Troubleshooting the RF Path (N5161A/62A/81A/82A)” on 

page 1-68

.

— If the signal generator does not achieve the maximum power levels:

a.

Replace the A2 Vector Module assembly.

b.

Proceed to 

“Troubleshooting the RF Path (N5161A/62A/81A/82A)” on page 1-68

.

•

If the signal generator is an N5183A and it does not meet one or more of the listed power levels in 

Table 1-12

, perform the 

troubleshooting procedure for the frequency range in which the low power occurred:

—

“No Output Power or Output Power is Unleveled (N5183A)” on page 1-40

—

“Low Output Power or No Output Power < 3.2 GHz (N5183A)” on page 1-41

—

“Low Output Power or No Output Power >= 3.2 GHz (N5183A)” on page 1-46

Troubleshooting the RF Path (N5161A/62A/81A/82A)

The ALC loop circuitry is part of the A3 RF assembly. It is likely an unleveled or under power condition is the result of a problem with the 
A3 RF assembly. 

•

For an N5161A/81A signal generator, replace the A3 RF assembly.

•

For an N5162A/82A signal generator,

1.

Verify that the A2 Vector Module is not contributing to the unleveled or under power condition. Refer to 

 

“A2 Vector Module Troubleshooting (N5162A/82A Only)” on page 1-29

.

2.

If the A2 Vector Module is not contributing to the condition, replace the A3 RF assembly.

Troubleshooting the 6 GHz Electronic Attenuator (N5161A/62A/81A/82A)

The 6 GHz electronic attenuator is built into the A3 RF assembly. It has an attenuation range of 130 dB, in 5 dB steps. The attenuator is used 
to rough tune the power level, while the ALC loop is used to fine-tune the power level. (The ALC fine tunes the power level within each 
5 dB step.) Due to the interactive design of the attenuator and the ALC loop, there is no precise setting that will predict when the attenuator 
will be switched in. The firmware, along with the selected frequency, the current ALC setting, modulation, and the requested attenuation all 
work together to determine the optimum instrument performance and when an attenuation step is switched in.

Aside from an A1 Power Supply failure, any suspected improper functionality of the attenuator requires the replacement of the A3 RF 
assembly.

The best way to troubleshoot the 6 GHz Electronic Attenuator is to run self test “601 Attenuator Voltages”. If this self-test cannot be run, 
perform the following steps:

1.

Refer to 

Figure 1-30

. Use a voltmeter with a small probe to measure the output v5.1V at J10-F23 and +/-15V at J10-A1 and 

J10-A3 on the A3 RF assembly.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments