manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 58 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 58

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Troubleshooting
Amplitude Modulation Problems (N5183A)

1-50

b.

Go to 

Chapter 4, "Post-Repair Procedures and Performance Verification"

.

•

If the measured voltages decrease by approximately 1V for each 10 dBm reduction in power level, as shown in the Example 
Voltages column in the table, verify the continuity of the W14 modulator drive cable (see 

Figure 1-19 on page 49

) to the A3 RF 

assembly.

— If the cable is bad, replace the cable.

— If the cable is good, replace the RF assembly.

12. Go to 

Chapter 4, "Post-Repair Procedures and Performance Verification"

.

Amplitude Modulation Problems (N5183A)

1.

Remove the external cover and the top inside cover. Refer to 

Chapter 3, "Assembly Replacement"

 for instructions on removing the 

instrument covers.

2.

Set up the signal generator:

a.

Press 

Preset

.

b.

Press 

FREQ

 > 

5

 > 

GHz

.

c.

Press 

RF On/Off

 to On.

d.

Press 

AMPTD

 > 

0

 > 

dBm

.

e.

Press 

AM

 > 

AM Off On

 to On.

f.

Press 

AM Type LIN EXP

 to EXP.

g.

Press 

AM Depth

 > 

40

 > 

dB

.

h.

Press 

AM Rate

 > 

400

 > 

Hz

.

Figure 1-20 ALC J1-E3

3.

Using an oscilloscope, measure ALC J1-E3 (

Figure 1-20

). 

NOTE

There is no “J1” label on this side of the circuit board.

You should see a sine wave with an amplitude > 2.5 Vp–p and a period of 2.5 ms.

J1-E3

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments