Agilent Technologies n5181a Service Manual Download Page 44

Page: 44 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting
Troubleshooting Assembly Level Problems

1-36

Refer to

Figure 1-11

. Using the voltmeter, measure A3J10-B16.

•

If A3J10-B16 is

∼

12V, perform the following steps:

Replace the A3 RF assembly.

Go to

Chapter 4, "Post-Repair Procedures and Performance Verification"

•

If A3J10-B16 is not

∼

12V, replace the A1 Power Supply.

A7 Micro Deck (N5183A)

•

•

LEDs

This procedure uses the LEDs on the A7 Micro Deck (

Figure 1-12

) for troubleshooting.

Figure 1-12 Micro Deck LEDs

Remove the external cover and the top inside cover. Refer to

Chapter 3, "Assembly Replacement"

for instructions on removing the

instrument covers.

Turn the signal generator on.

Observe the LEDs shown in

Figure 1-12

•

DS1 (green) LED normal operation: blinks twice, then pauses and repeats.

If normal operation is not present, check LED DS7.

If DS7 is on, check DS7 as described below.

•

DS2 to DS5 (amber) LEDs have no significance in troubleshooting the instrument.

•

DS6 (red) LED is normally off. If DS6 is on, it indicates FPGA code is missing.

— Reload the firmware.

•

DS7 (red) LED is normally off. When DS7 is on, it indicates a missing PCI clock.

Check J1-F24 (see

Figure 1-13 on page 37

for test point locations) for a sine wave (

3 Vp–p at

∼

32 MHz, period

∼

31 ns).

If the signal is < 3 Vp–p:

Replace the A3 RF assembly.

Go to

Chapter 4, "Post-Repair Procedures and Performance Verification"

DS7

DS2

DS3

DS4

DS5

DS1

DS6

深圳德标仪器

135-1095-0799

Summary of Contents for n5181a











































































































































































































Search results

Summary of Contents for n5181a

Reviews:

Agilent Technologies n5181a, Service Manual, Page: 44 / 202

Search results

Summary of Contents for n5181a

Reviews: