manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 140 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 140

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Assembly Replacement
A1 Power Supply

3-28

A1 Power Supply

Tools Required 

•

T-10 driver 

Removal Procedure 

Refer to 

Figure 3-14

 for this procedure.

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

, and 

”Inner Top Cover” on page 3-6

.

3.

Remove the rear panel from the signal generator. Refer to 

“Rear Panel (N5161A/81A)” on page 22

, 

”Rear Panel (N5162A/82A)” on 

page 3-24

, or 

”Rear Panel (N5183A)” on page 3-26

.

NOTE

The rear panel must be removed so the power connector on the A1 Power Supply can be disconnected from the A3 RF assembly 
without damaging the connector pins.

4.

Place the signal generator flat and upright with the front-panel facing you.

5.

Using the T-10 driver, press the connector latch to disconnect B1W1 thru B4W1 from the A1 Power Supply.

6.

Using the T-10 driver, remove the five screws (1) that secure the A1 Power Supply to the chassis.

7.

Remove the A1 Power Supply.

Replacement Procedure 

1.

Reverse the order of the removal procedure.

2.

Torque all screws to 9 in–lbs.

3.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments