Agilent Technologies n5181a Service Manual Download Page 134

Page: 134 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Assembly Replacement
Rear Panel (N5161A/81A)

3-22

Rear Panel (N5161A/81A)

Tools Required

•

T-10 driver

•

5/8” hex-nut driver

Removal Procedure

Refer to

Figure 3-11

for this procedure.

Disconnect the power cord.

Remove the covers from the signal generator. Refer to

”Outer Cover” on page 3-4

”Inner Top Cover” on page 3-6

, and

”Inner Bottom

Cover” on page 3-8

Place the signal generator flat with the rear panel facing you.

Using the 5/8” hex-nut driver, remove the nuts and washers (1) securing the A3 RF assembly BNC’s to the rear panel.

Using the T-10 driver, remove the four screws (2) securing the rear panel to the signal generators chassis.

Pull the rear panel away from the signal generator’s chassis.

Replacement Procedure

Reverse the order of the removal procedure.

Torque all screws to 9 in–lbs.

Torque all BNC connectors to 8 in–lbs.

Perform the post-repair performance tests that pertain to this replacement procedure, see

Chapter 4, Post-Repair Procedures and

Performance Verification

深圳德标仪器

135-1095-0799

Summary of Contents for n5181a











































































































































































































Search results

Summary of Contents for n5181a

Reviews:

Agilent Technologies n5181a, Service Manual, Page: 134 / 202

Search results

Summary of Contents for n5181a

Reviews: