Agilent Technologies GS8210 Programming Manual Download Page 39

Page: 39 / 352

Programming Command Guideline

N9360A Multi UE Tester GSM Programming Manual

4-5

Overview of the Ethernet Interface

Settings for the Ethernet Interface

Refer to the documentation on your controller, programming
language, and a LAN card to configure the Ethernet interface.

The Ethernet configuration is not programmable but manually
set using the User Interface. The preset settings and allowable
range are as follows:

The terminator outputted from the Tester can be changed as
specified in

Table 4-1

The terminator inputted to the Tester is LF (fixed).

The TCP port number is 10123 (fixed).

User cannot use the address from 192.168.1.1 to 192.168.1.255
as it is already used by the Tester.

Refer to the following procedure to set the Ethernet
configuration.

Table 4-1 Ethernet configuration

Item

Preset

Allowable Range

IP Addr

192.168.0.1

1.0.0.1 to 223.255.255.255

CIDR (Mask)

24(255.255.255.0)

1 to 31

Gateway

NONE

NONE, ACT

Addr

0.0.0.0

1.0.0.1 to 223.255.255.255

Terminator

CR+LF

CR+LF, CR, LF

Summary of Contents for GS8210

































































































































































































































































































































































Search results

Summary of Contents for GS8210

Reviews:

Agilent Technologies GS8210, Programming Manual, Page: 39 / 352

Search results

Summary of Contents for GS8210

Reviews: