Agilent Technologies G1314B User Manual Download Page 97

Page: 97 / 208

Agilent 1260 Infinity VWD User Manual

Error Information

Detector Error Messages

Wavelength calibration setting failed

Error ID: 7310

The intensity maximum was not found during wavelength calibration.

Calibration 0 Failed:

Zero-order calibration failed.

Calibration 1 Failed:

656 nm calibration failed.

Probable cause

Suggested actions

Lamp is OFF.

Switch on the lamp.

Incorrect flow cell installation.

Ensure the flow cell is installed correctly.

Flow cell contamination or air bubbles.

Clean/replace flow cell windows or remove air
bubbles.

Intensity too low.

Replace lamp.

Current step value too far from maximum.

•

Repeat the calibration.

•

Please contact your Agilent service
representative.

Misaligned/defective grating assembly.

Please contact your Agilent service
representative.

Defective main board.

Please contact your Agilent service
representative.

Summary of Contents for G1314B

















































































































































































































Search results

Summary of Contents for G1314B

Reviews:

Related manuals for G1314B

Brands by name

Popular brands

Agilent Technologies G1314B, User Manual

Search results

Summary of Contents for G1314B

Reviews:

Related manuals for G1314B

Brands by name

Popular brands