manualshive.com logo in svg

Agilent Technologies E8363A, Installation Note

Share
Download
Agilent Technologies E8363A Installation Note Download Page 5

Installation Note E8364-90012                                                                                                                         

 

5

Items Included in the Upgrade Kit

Table 1

 lists the parts included in this upgrade kit, Agilent part number E8364-60101. Check 

the contents of your kit against this list. If any item is missing or damaged, contact Agilent 
Technologies. Refer to 

“Getting Assistance from Agilent” on page 3

.

Table 1

Contents of Option 014 Upgrade Kit (E8364-60101)

Ref Desig.

Description

Qty

 Part Number

The following parts are required for all analyzers

Installation note (this document)

1

E8364-90012

Cable clamp

1

1400-1439

W60

Front-panel jumper

6

E8364-20059

W65

RF cable, A23 detector to REFERENCE 1 SOURCE OUT

1

E8364-20047

W66

RF cable, A24 detector to REFERENCE 2 SOURCE OUT

1

E8364-20048

W67

RF cable, A25 test port 1 coupler to PORT 1 CPLR ARM

1

E8364-20043

W68

RF cable, A26 test port 2 coupler to PORT 2 CPLR ARM

1

E8364-20044

W69

RF cable, PORT 1 RCVR A IN to A27 channel A mixer

1

E8364-20045

W72

RF cable, PORT 2 RCVR B IN to A30 channel B mixer

1

E8364-20046

The following parts are required for only analyzers without Option UNL installed

Lower front panel overlay (Option 014)

1

E8364-80004

W61

RF cable, A22 switch splitter to PORT 1 SOURCE OUT

1

E8364-20081

W62

RF cable, A22 switch splitter to PORT 2 SOURCE OUT

1

E8364-20082

W63

RF cable, PORT 1 CPLR THRU to A25 test port 1 coupler

1

E8364-20073

W64

RF cable, PORT 2 CPLR THRU to A26 test port 2 coupler

1

E8364-20074

W70

RF cable, REFERENCE 1 RCVR R1 IN to A28 channel R1 
mixer

1

E8364-20075

W71

RF cable, REFERENCE 2 RCVR R2 IN to A29 channel R2 
mixer

1

E8364-20076

The following parts are required for only analyzers with Option UNL installed

Lower front panel overlay (Option UNL/014)

1

E8364-80011

W70

RF cable, REFERENCE 1 RCVR R1 IN to A28 channel R1 
mixer

1

E8364-20049

W71

RF cable, REFERENCE 2 RCVR R2 IN to A29 channel R2 
mixer

1

E8364-20050

W81

RF cable, A36 step attenuator to PORT 1 SOURCE OUT

1

E8364-20053

W82

RF cable, A37 step attenuator to PORT 2 SOURCE OUT

1

E8364-20054

W83

RF cable, PORT 1 CPLR THRU to A38 bias tee

1

E8364-20039

W84

RF cable, PORT 2 CPLR THRU to A39 bias tee

1

E8364-20040

Summary of Contents for E8363A





















Reviews:

No comments

Brands by name

Popular brands

Load more brands