manualshive.com logo in svg

Agilent Technologies E4400-60246, Installation Note, Page: 20 / 22

Share
Download
Agilent Technologies E4400-60246 Installation Note Download Page 20

 20                                                                                                                                  Installation Note E4400-90392

Checking Option 300 Functionality

The following procedure verifies the operation of Option 300 by looping the uplink 
transmitted signal directly back to the ESG. 

Configure the ESG  1.Refer to 

Figure 5

. Connect the RF output to the 321.4 IN connector on 

the rear of the signal generator. 

Figure 5 

Equipment Setup

2. Press 

Preset

.

3. Press 

Frequency

 > 

321.4

 > 

MHz

, then press 

Amplitude

 >

 

−

10

 > 

dBm

.

4. Press 

RF ON/OFF

. 

The 

RF ON

 annunciator is now displayed.

5. Press 

Mode

 > 

BERT

 > 

BTS BERT EDGE Loopback

 > 

Configure Measurement

 > 

Transmit Settings

.

6. Press 

Data Format Pattern Framed

 until Framed is highlighted.

7. Press 

Configure Timeslots

 > 

Configure Normal

 > 

E

 > 

Multiframe Channel

 > 

Uncoded

 > 

PN9

 > 

Return

 > 

Return

 > 

Return

 > 

Return

.

8. Press 

EDGE ON/OFF

. 

ON is now highlighted indicating that the EDGE transmission is active.

Summary of Contents for E4400-60246























Reviews:

No comments