manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 224

224

5977B Series MSD Troubleshooting and Maintenance Manual

8

Electronics

Interfacing to External Devices

Remote control processor

The remote control processor on the LAN/MS control card synchronizes 
start-run signals with GCs and other devices. The functions of the remote 
control processor are extended to the remote start (Remote) connector 
(

Figure 54

) on the back panel of the MSD. The remote start cable connects the 

GC and the MSD.

Remote start signals

It is often necessary to communicate with external devices (for example, a 
purge-and-trap) during a run. Typically, these communications are requests to 
send a system-ready signal. They also include:

•

Receive a start run signal from an external device

•

Program the timing of events during a run

 

System ready

When interfacing to an external device, it is often desirable to send a 
system-ready signal to the device. In the case of a multisample Tekmar 
purge-and-trap, each sample is purged onto a trap where it waits for a ready 

Figure 54  

Remote start connector

Start

Ground

Ready

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands