manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 169

Vacuum System

6

5977B Series MSD Troubleshooting and Maintenance Manual

169

Diffusion Pump and Fan

The diffusion pump in the MSD is an air-cooled vapor diffusion pump with 
90 L/s capacity. It mounts with a KF50 fitting to a baffle adapter clamped to 
the bottom of the analyzer chamber.

The diffusion pump has a cylindrical body surrounded by fins to help 
dissipate heat. Its inlet is open to the interior of the analyzer chamber, through 
the adapter and baffle. A structure called the stack is located at the center of 
the pump body. An electric heater is located at the bottom of the stack. 
See 

Figure 33

 on page 169 and 

Figure 34

 on page 170.

Figure 33  

Diffusion pump with fan

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands