manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 162

162

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

Analyzer Chamber 

The analyzer chamber (

Figure 29

) is where the analyzer operates. The 

manifold is extruded and machined from an aluminum alloy. Large openings 
in the side, front, and rear of the analyzer chamber are closed by plates. 
O-rings provide the seals between the plates and the manifold. Ports in the 
manifold and the plates provide attachment points for the Micro-Ion vacuum 
gauge, calibration valve, vent valve, GC/MSD interface, and high vacuum 
pump.

Diffusion pump version

The diffusion pump attaches, with a KF50 seal, to a baffle adapter that is 
clamped to the bottom of the manifold. A vapor baffle helps prevent migration 
of pump fluid vapor into the manifold. Cooling fins on the bottom of the 
manifold keep the baffle cool so the vapor will condense on it.

Turbo pump version

The turbo pump and the mounting bracket for the turbo controller are 
clamped directly to the manifold.

Figure 29  

Analyzer chamber

Vacuum gauge baffle

GC/MSD interface

To high vacuum pump

Calibration and vent valves

Observation window

Side plate O-ring

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands