manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 157

Vacuum System

6

5977B Series MSD Troubleshooting and Maintenance Manual

157

Foreline Pump

The foreline pump reduces the pressure in the analyzer chamber so the high 
vacuum pump can operate. It also pumps away the gas load from the high 
vacuum pump. The foreline pump is connected to the high vacuum pump by a 
130-cm hose called the foreline hose. There are four different types of foreline 
pumps, the Pfeiffer DUO (

Figure 26

), the MVP-070-3 (

Figure 27

 on page 158), 

the MVP-070-3C (not shown), and the IDP3 (

Figure 28

 on page 158). The dry 

foreline pumps are not supported with diffusion pump base MSDs

Figure 26  

Pfeiffer DUO foreline pump

Hose to vacuum pump

Ballast control

Fill cap

Exhaust outlet

Power switch

Oil level window

with oil mist filter

Drain plug (on front)

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands