manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 150

150

5977B Series MSD Troubleshooting and Maintenance Manual

5

CI Maintenance

To Refill the CI Calibrant Vial

Materials needed

•

PFDTD calibrant (8500-8510)

Procedure

1

Set the reagent gas flow to 

Gas Off

.

2

Vent the MSD. 

3

Remove the capillary column from the GC/MSD interface.

4

Pull the MSD away from the GC to expose the calibration vial and valve. 
See

 “To Separate the MSD from the 7890 GC” 

on page 97.

5

Loosen the collar holding the calibration vial in place. Do not remove the 
collar.

6

Remove the calibrant vial. See 

Figure 24

 on page 151.

7

Fill the vial no higher than the bottom of the internal tube with fresh 
PFDTD calibrant (8500-8510).

8

Replace the vial and tighten the collar.

9

Reposition the MSD next to the GC. See

 “To Reconnect the MSD to the 7890 

GC” 

on page 101.

10

Reinstall the capillary column.

11

Pump down the MSD. 

12

Purge the calibration valve. See

 “To Purge the Calibration Valves” 

on 

page 130.

    

             

C A U T I O N

Do 

not 

rinse the vial with any solvents. 

Never

 expose the inside of the vial to 

chlorinated solvents or isopropyl alcohol or water — this will result in severe loss of CI 
sensitivity.

C A U T I O N

After removing the calibrant vial, you 

must

 purge the calibration valve. Failure to do so 

will result in severe contamination of the ion source and damage to the filament and 
electron multiplier.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands