manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 130

130

5977B Series MSD Troubleshooting and Maintenance Manual

4

General Maintenance

To Purge the Calibration Valves

EI calibration valve

After adding new PFTBA to the calibrant vial, you must purge the air out of 
the vial and valve. 

1

If the vacuum gauge controller is on, turn it off.

2

In 

Tune and Vacuum Control 

view, select 

Purge Calibrant Valve 

under the 

Vacuum menu. 

This will open the CI calibration valve for several minutes with all analyzer 
voltages turned off.

CI calibration valve

After adding new PFDTD to the calibrant vial, you must purge the air out of 
the vial and valve. 

1

If the vacuum gauge controller is on, turn it off.

2

Verify that 

PCICH4.U 

is loaded.

3

In 

Tune and Vacuum Control

 view, select 

Purge Calibrant Valve

 under the 

Vacuum menu. 

This will open the CI calibration valve for several minutes with all analyzer 
voltages turned off.

C A U T I O N

After removing a calibrant vial, you 

must

 purge the calibration valve. Failure to do so 

will result in damage to the filaments and the electron multiplier.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands