manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 143

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

143

To Adjust the Quad Frequency

Materials needed

•

Screwdriver, flat-blade, large (8730-0002)

Procedure

1

Ensure the MSD is at thermal equilibrium. It takes at least 2 hours 

after

 all 

heated zones have reached their setpoints for the MSD to reach thermal 
equilibrium.

2

Open the analyzer cover. 

3

Ensure the RF cover on the side board is secure and no screws are missing. 
A loose RF cover or missing screw can 

significantly

 affect coil adjustment.

4

In the 

Tune and Vacuum Control 

view, select 

Optimize Quadrupole Frequency 

from 

the Execute menu

.

5

Enter an 

m/z 

value of 100.

6

Slowly turn the quad frequency adjustment screws to minimize the voltage 
displayed. (See 

Figure 22

 on page 144.)

Turn the adjustment screws alternately. Turn each screw only a little bit at 
a time. Keep the screws at 

equal

 extension.

7

When the voltage is minimized, click 

Stop

.

    

             

WA R N I N G

Do not remove any other covers. Dangerous voltages are present under these 
covers.

C A U T I O N

Do not use a coin to adjust the screws. If you drop it, it could fall into the electronics 
fan and cause significant damage.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands