Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 102 | Manualshive

Page: 102 / 258

Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 102

102

5977B Series MSD Troubleshooting and Maintenance Manual

4

General Maintenance

To Reconnect the MSD to the 9000 GC

This procedure starts with both instruments shut down and at room
temperature.

Procedure

1

Position the MSD so the end of the GC/MSD interface is near the GC. (See

2

Tighten the thumb screw at the top of the interface heater clamp. If the
thumb screw is loose when reconnecting the GC/MSD, it will be difficult to
retighten when installing the 9000 GC/MSD Tail.

3

Connect the GC/MSD interface heater cables and LVDS cable.

4

Slide the MSD against the GC with the transfer line entering the GC side
opening, and the metal brackets entering their slots in the base of the GC.

Be careful not to damage the GC/MSD interface as it passes into the GC.

5

Open the GC front door.

6

Slide the MS forward until the GC/MSD interface lightly contacts the bus.
(See

.)

«
...
100
101
102
103
104
...
»

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands