Agilent Technologies 5977B CI MSD Operating Manual Download Page 174 | Manualshive

Page: 174 / 254

background image

7

General Maintenance



Maintaining the Analyzer

174

5977B Series MSD Operating Manual

Maintaining the Analyzer

Scheduling

None of the analyzer components require periodic maintenance. Some tasks,
however, must be performed when MSD behavior indicates they are necessary.
These tasks include:

•

Cleaning the ion source

•

Replacing filaments

•

Replacing the electron multiplier horn

The

Agilent 5977B Series MSD Troubleshooting and Maintenance Manual

provides information about symptoms that indicate the need for analyzer
maintenance. The troubleshooting material in the online help in the Agilent
MassHunter GC/MS Acquisition software provides more extensive information.

Precautions

Cleanliness

Keep components clean during analyzer maintenance. Analyzer maintenance
involves opening the analyzer chamber and removing parts from the analyzer.
During analyzer maintenance procedures, take care to avoid contaminating the
analyzer or the interior of the analyzer chamber. Wear clean gloves during all
analyzer maintenance procedures. After cleaning, parts must be thoroughly
baked out before they are reinstalled. During and after cleaning, analyzer parts
should be placed only on clean, lint-free cloths.

CAUTION

If not done correctly, analyzer maintenance can introduce contaminants into
the MSD.

WARNING

The analyzer operates at high temperatures. Do not touch any part until you
are sure it is cool.

«
...
172
173
174
175
176
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: A.O. Smith Pages: 2

Brand: DAB Pages: 13

Brand: Samsung Pages: 27

Brand: ULTIMATE SPEED Pages: 52

Brand: Balcrank Pages: 18

Brand: Calorex Pages: 24

Brand: Fairland Pioneer Pages: 36

Brand: SAER Elettropompe Pages: 44

Brand: Beckett Pages: 2

Brand: Macon Pages: 24

Brand: Barmesa Pumps Pages: 13

Brand: Lochinvar Pages: 1

Brand: Cala Pages: 21

Brand: DAYLIFF Pages: 12

Brand: A.O. Smith Pages: 2

Brand: Makita Pages: 109

SOLAR FLOW 22-02

Brand: La Buvette Pages: 43

Aquarius Universal Classic 600

Brand: Oase Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands