Agilent Technologies 5977B CI MSD Operating Manual Download Page 139 | Manualshive

Page: 139 / 254

background image

5

Operating in EI Mode



To Pumpdown the MSD

5977B Series MSD Operating Manual

139

To Pumpdown the MSD

You can also use the 8890 or 7890B GC control panel to perform this task. (See
also

“Operating the MSD from the 7890 GC Control Panel”

Procedure

1

Remove the analyzer window cover and open the analyzer cover. (See

Open the MSD Covers”

2

Verify that the foreline pump inlet valve is open.

3

Verify that the vent valve is open by turning it clockwise until closed. (See

WARNING

Make sure your MSD meets all the conditions listed in the introduction to this
chapter before starting up and pumping down the MSD. (See

“Before You Turn

on page 113.) Failure to do so can result in personal injury.

WARNING

Never open the vent valve without first closing the hydrogen supply line to all
possible sources of hydrogen entry to the analyzer. This requires closing the
hydrogen shutoff valve to the carrier gas flow module and the shutoff valve to
the JetClean system supply if either of these hydrogen sources exist on the
instrument. Read

“Hydrogen Safety”

on page 24 before operating the MSD

with hydrogen gas.

CAUTION

Agilent does not recommend using hydrogen as a carrier gas on systems
equipped with an IDP3 foreline pump.

WARNING

Do not open the vent valve without verifying that the JetClean system
hydrogen supply shutoff valve is closed if the optional JetClean system is
installed. Refer to the JetClean system Operating manual for warnings
regarding hydrogen safety when the hydrogen shutoff valve is open.

«
...
137
138
139
140
141
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Gardena Pages: 13

Brand: WarmFlow Pages: 89

Brand: Calpeda Pages: 44

Brand: Calpeda Pages: 64

Brand: Calpeda Pages: 32

Brand: Danfoss Pages: 34

Brand: Danfoss Pages: 52

607 challenger series

Brand: National Vacuum Equipment Pages: 20

Brand: Vagner Pool Pages: 35

Brand: A.O. Smith Pages: 4

OmniSpense ELITE

Brand: Wheaton Pages: 34

Altherma 3 M Series

Brand: Daikin Pages: 24

Brand: German pool Pages: 17

Brand: Versamatic Pages: 18

Brand: K&T Pages: 17

Alterma EDHQ011AA6V3

Brand: Daikin Pages: 22

Lincoln 215-M049

Brand: SKF Pages: 45

Brand: laguna Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands