manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual, Page: 113 / 254

Share
Download
Agilent Technologies 5977B CI MSD Operating Manual Download Page 113

5

Operating in EI Mode

Before You Turn On the MSD

5977B Series MSD Operating Manual

113

Before You Turn On the MSD

Verify the following 

before

 you turn on or attempt to operate the MSD.

•

The vent valve should be open slightly (knob turned 45 degrees 
counterclockwise from the fully closed position).

•

All other vacuum seals and fittings must be in place and fastened correctly. 
The front side plate screw should not be tightened, unless hazardous carrier, 
JetClean system hydrogen, or reagent gases are being used.

•

The MSD is connected to a grounded power source.

•

The GC/MSD interface extends into the GC oven.

•

A conditioned capillary column is installed in the GC inlet and in the GC/MSD 
interface.

•

The GC is on, but the heated zones for the GC/MSD interface, the GC inlet, 
and the oven are off.

•

Carrier gas of at least 99.9995% purity is plumbed to the GC with the 
recommended traps. The regulator, plumbing, traps, EPC module, inlet, and 
column have been purged of any gas to remove oxygen from the system.

•

If hydrogen is used as carrier gas, or JetClean system supply, the carrier gas 
and JetClean system supply shutoff valves must be closed, and the analyzer 
top sideplate thumbscrew must be loosely fastened.

•

The foreline pump exhaust is properly vented.

WARNING

The exhaust from the foreline pump contains solvents and the chemicals you 
are analyzing. If using the standard foreline pump, it also contains traces of 
pump oil. If you are using toxic solvents or analyzing toxic chemicals, remove 
the oil trap (standard pump) and install a hose to take the foreline pump 
exhaust outside or to a fume (exhaust) hood. Be sure to comply with local 
regulations. The oil trap supplied with the standard pump stops only pump oil. 
It does not trap or filter out toxic chemicals.

WARNING

If hydrogen is used as a carrier gas or JetClean system supply, the carrier and 
JetClean system supply shutoff valves must be closed before turning off the 
MSD power. If the foreline pump is off, hydrogen will accumulate in the MSD 
and an explosion may occur. Read 

“Hydrogen Safety” 

on page 24 before 

operating the MSD with hydrogen gas.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments