Agilent Technologies 53210A Options Installation Download

Page: 7 / 44

53210A/53220A/53230A Option Installation

3. Using a 5/16" open end wrench, loosen the SMA connector on the end

of the semi- rigid cable that is connected to the PC board.

4. Slide the Option 106/115 assembly to the rear of the chassis, as neces-

sary, to expose the two gold- connectors at the front of the motherboard

near the front panel (J101 and J201).

Ultra-High Stability Timebase (Option 010)

GPIB Interface (Option 400)

Option 400 GPIB Connector Parts (53200U - 400)

Item

Agilent Part No.

Qty.

•

PC Board Assembly

P0001-63001

•

Ribbon Cable, 16-pin

53200-61601

•

7mm Hex-head standoff

0380-0644

•

Washer, lock

2190-0577

N O T E

Option 010 (Ultra-High Stability Timebase) must be performed by technicians at an
Agilent Technologies Service Center. Go to

www.agilent.com/find/assist

for

information on contacting Agilent in your region, or contact your Agilent Technol-
ogies Representative.

N O T E

To order the Ultra-High Stability Option 010, you will need to place an order with
Agilent for 53200U-010 and identify which counter you have (Agilent 53210A,
53220A, or 53230A).

Summary of Contents for 53210A













































Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands

Agilent Technologies 53210A, Options Installation

Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands