Agilent Technologies 34945A User Manual Download Page 60

Page: 60 / 124

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Software Installation and Configuration

Firmware and Driver Updates

irmware and driver updates (when available) for the 34980A are available via

the Web. This section contains information for locating and downloading the

updates to your computer, and then installing the updates in the instrument.

Downloading and Installing the Update Utility

34945A firmware updates are installed in the instrument using the Agilent

Firmware Update Utility. The utility and firmware update can be found on the

Web at:

www.agilent.com/find/34980A

Once this page is displayed, highlight ‘Technical Support’ and from the Techni-

cal Support window select ‘

Drivers and Software

’. Within the drivers and

software list, scroll to and select:

34980A Firmware Update Revision <

revision number

From this window, go to ‘Documents and Downloads’ and select:

Agilent 34980A Firmware Update Utility

When prompted, select ‘Run’ to install the utility. The default installation

directory is C:\Program Files\Agilent\Firmware Update Utility. The utility

will also be added to the ‘start’ menu under “Agilent”.

Downloading the Firmware Update

Return to the Web page and under “Documents & Downloads and select:

Agilent 34980A Firmware Revision <

revision number

When prompted, select ‘Run’ to extract and download the file to your PC.

Note

the directory location as you will need to specify the path to the firmware

file when you run the update utility.

N O T E

Depending on the interface to the 34945A, the firmware update utility will require
the instrument’s LAN, GPIB, or USB address. Note this address before starting the
utility.

Summary of Contents for 34945A





























































































































Search results

Summary of Contents for 34945A

Reviews:

Related manuals for 34945A

Brands by name

Popular brands

Agilent Technologies 34945A, User Manual

Search results

Summary of Contents for 34945A

Reviews:

Related manuals for 34945A

Brands by name

Popular brands