manualshive.com logo in svg

Agilent Technologies 3070 Series, Site Preparation

Share
Download
Agilent Technologies 3070 Series Site Preparation Download Page 111

©

 

Agilent Technologies 1989–2002

Agilent 3070 / 79000 Site Preparation

 7-3

Chapter 7: Site Preparation – Compressed Air and Vacuum Requirements: Compressed Air Requirements

3000 Push-tite 1/4-inch female coupling or equivalent 
(Agilent PN 0100-1655). The testhead air input 
connector is shown in 

Figure 7-1

 on page 7-3.

Figure 7-1

Compressed air connection to the testhead

Air Quality

The compressed air must be oil-free and must meet the 
humidity specifications in 

Table 7-1

. We recommend 

that the air be filtered to remove contaminants such as 
oil and aerosols. The filter should filter 0.3-micron 
particles.  

AIR2.WPG

03066-67911

Air Output for

external

applications

Air Input

connector on

rear of testhead

Air regulator

inside testhead

0100-1655

female

coupling

Summary of Contents for 3070 Series



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands