manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 151

 
 
DD+DIS033.07E 

Repair and Service

Tools and Auxiliary Means

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

3.6.2 

Printer Bootup-Message 

 

Purpose 

The printer terminal level provides following service action: 

•

 

An online logging, which displays all actions of the printer software during 
bootup. 
 

 

 

The printer terminal level is not intended to be used as official service tool. 

It is only used for troubleshooting, e.g. to view the boot-up messages. 

 

 

Usage 

(1)  Connect the Service PC to the 

printer as displayed in Figure 
41. 

(2)  Start the HyperTerminal as 

displayed in section 3.6.2.1.  

(3)  Switch the printer on: 

Now the bootup message 
appears 

(4)  When the Printer login appears 

the bootup message is finished. 

536632ep.cdr

 

 

 

Figure 41 

 

3.6.2.1 

Setup of the HyperTerminal 

 

NOTE: 

The hyper terminal setup as displayed here can be used for all AGFA devices. 

Instead of the HyperTerminal following other programs can be recommended to 
connect to terminal level: 

•

 xt. 

 

xt.exe is an AGFA program, which is part of the IMOS package. It can be started 
in a DOS box by typing ‘xt’ 

•

 IMOS 

Start 

Menu. 

The IMOS Start Menu software has a terminal built in. Select ‘tools - terminal’. 
Depending on the configuration of IMOS Start, either a DOS box with xt will be 
opened or a Hyper terminal window will pop-up. 

 

 

(1)  To start the setup of the HyperTerminal, go to ‘Programs - Accessories - 

HyperTerminal - HyperTerminal’ 

 

Edition 1, Revision 0 

DRYSTAR AXYS 

Chapter 3.2 / 45 

10-2007 Type 

5367/100 

Agfa Company Confidential

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands