AGCO Challenger MT255B Service Manual Download

Page: 6 / 31

79024230 A Rev.

01-3

General Information

Specifications

TABLE 1

1528 / ST28A / MT255B

4WD

1531 / ST33A

4WD

Dimensions (with Agri-tires): (inch) mm

Overall length

2855 (112.4)

Overall width

1360 (53.5) Ag and Turf Tires

1680 (66.1) R4 Tires

Overall height (to the top of steering wheel)

1400 (55.1)

Overall height (to the top of ROPS)

2050 (80.7)

Wheel base

1665 (65.6)

Wheel tread Front (6-14)

960 (37.8)

Rear (12.4-16)

1096 (43.2)

Minimum ground clearance (under PTO

bottom)

200 (7.9)

Minimum turning radius: without brake

5600 (220.5)

Weight (with Rops and Seat) lb (kg)

1000 (2204.6)1005 ( 2215.6)

1100 (2423)

ENGINE

Make

Iseki Diesel

Model

E3CF-VB22

E3CD-VB32

Type

Water-cooled, 4-cycle, 3-cylinder, Diesel, Indirect injection,

overhead valve

Aspiration

Natural

Displacement in

(cc)

1463 (89.3)

1498 (91.4)

Find manuals at https://best-manuals.com

Summary of Contents for Challenger MT255B
































Search results

Summary of Contents for Challenger MT255B

Reviews:

Related manuals for Challenger MT255B

Brands by name

Popular brands

AGCO Challenger MT255B, Service Manual

Search results

Summary of Contents for Challenger MT255B

Reviews:

Related manuals for Challenger MT255B

Brands by name

Popular brands