CLIPPER T004 – Professional clipper AGC CREATION
Instructions for use, maintenance, and safety
PLEASE READ THESE INSTRUCTIONS CAREFFULY BEFORE USING THE CLIPPER.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
: To reduce the risk of burns, fire, electric shock or injury:
- Never use the clippers for anything other than the purpose for which it is
designed.
- The machine must not be used outdoors and in wet locations. It must be
kept away from water.
- Check that the voltage indicated on the clipper corresponds to your
electrical supply. Your electrical supply should meet current safety
standards and be fitted with a 30 mA circuit breaker.
- Use only accessories and power cord supplied with the machine
- This machine is not designed to be used by people (including children)
whose physical, sensory, or mental capacities are reduced, or by anyone
without the necessary skills or knowledge, unless they are specifically
monitored or have been instructed in the use of the machine by somebody
responsible for their safety".
- Never allow children or unskilled persons to use the clipper without
supervision.
- Do not use this machine if:
- If the power cord is damaged,
- In case of malfunction,
- If the machine has been damaged in any way,
- If you dropped the machine or,
- Has been dropped in water.
Take the machine to a technical assistance centre for inspection and repair
if necessary
- If the power cable is damaged, it should be discarded and replaced with
an identical model.
- Make sure to keep the machine away from hot surfaces.
- Do not expose to direct sunlight and dust.
- Do not wrap the cord around the appliance when storing. The friction
on the cord may damage the insulation and cause a risk of short circuit.
- Do not use a cutting blade with a missing tooth or if it is damaged as
you will cut you. Make sure the blades are aligned and oiled
- Avoid touching the blades when they are moving.
- Make sure that the power cord can not be walked on or pinched
particularly at the power supply, power outlets, and the connection
point of the machine.
- Always unroll the power cord when using (in order to avoid
overheating).
- Never unplug the machine by pulling on the cordless but by pulling
the power socket
- When cleaning the machine, always unplug from the electrical outlet.
- Do not use the clipper on wet coat. Moreover, you will not have any
results because it is designed to cut dry coat.
DANGER: RISK OF ELECTRIC SHOCK!
Never immerse the machine in water or any other liquid.
Similarly, do not use this machine near water or moisture source such
as a bathtub, sink, kitchen sink, swimming pool, or other location where
there is risk projection of water.
- Never use the clipper with wet hands.
If the clipper fall into water and it’s connected to the power supply,
unplug the power supply before picking up the clipper
- If the clipper stop working or do not work correctly, turn it off and do
not open it. Repairs should only be performed at a technical assistance
centre.
NEVER OPEN THE CLIPPER
TECHNICAL SPECIFICATIONS
Clipper T004 – 2 speeds …….. 220-240 V – AC 50-60 Hz - 45 watts
USE OF THE CLIPPER
Make sure that the clipper and the blade are clean before starting to clip,
as dirt will prevent the clipper from running smoothly.
Plug into the power outlet. Lubricate the blade
Turn the clipper on with the on / off switch and turn off the clipper after
use.
This model of clipper operates on main power.
If after a period of use, your clipper does not perform as well as before,
we advise replacing the blade or making it sharpens. The use may be
compromised by the presence of electrical contacts that are unclean.
REPLACEMENT OF THE BLADE
The clipper makes it possible to leave different lengths of cut either by
using different blades provided in option in the range AGC
CREATION, Oster, Wahl, Moser, Andis.
.
picture 1
picture 2
To replace the blade, turn the clipper OFF, release the blade while
supporting on the spring and in the center of the blade (picture 1) then
to make slide on the hinge (picture 2). To position back the blade, put
the clipper in position ON, insert the blade on the hinge then to press it
until hearing the clac blocking.
CLEANING AND MAINTENANCE
Before cleaning, turn off the clipper and remove the plug from the
power socket..
Use a soft and dry cloth to clean the body of the clipper.
- Do not use abrasive cleaners, scouring pads or substances such as
alcohol or acetone to clean the clipper.
- To ensure that the clipper continues to produce a high quality of cut,
blades should be cleaned and lubricated regularly (lubrifiant AGC
CREATION ref C703 sold separately).
- After each use, remove the remains of coat of
the blade using a cleaning brush.
- Do not use inappropriate solvents (greases, e.g
cream, etc)
ENVIRONMENT – Waste sorting
This symbol on the product or its packaging indicates that this product
should not be treated with household waste. It must be given to a
suitable collection point for the recycling of electrical and electronic
equipment. Place this product in a collection point or in a waste
collection centre.
6 Bd de Chinon - 37510 BALLAN MIRE – France – www.agc-creation.com
Tel : +33 (0)982 301 429 – Fax : +33 (0)982 639 023 - email : [email protected]
GUARANTEE
The clipper is guaranteed for a period of 12 months from the date of purchase, the guarantee terminates at this time even if the clipper has not
been used. It is therefore advisable to keep the proof of purchase (receipt and original packaging). The guarantee is applicable for normal
conditions of use and not intensive, on clean materials with regular maintenance of all parts. The guarantee covers all mechanical and electrical
manufacturing defects. The replacement or repairs of parts that are subject to normal wear, such as the blades, power cable are therefore excluded.
Any repairs made during the guarantee period do not result in a prolongation of the latter. The guarantee is not valid if the clipper has been opened
or damaged as a result of negligence, inexperience, or during transport. The replacements or repairs covered by the guarantee are free of charge
by sending the clipper directly (Shipping cost are to expense of the purchaser), in its original packaging, with proof of purchase to:
AGC CREATION - 6 Bd de Chinon – 37510 BALLAN MIRE - FRANCE
