background image

7

C A R E   O F   T H E   U N I T

Care of Unit

1. Avoid leaning on the cabinet door. You may

bend the door hinge or tip the unit.

2. Exercise caution when sweeping, vacuuming,

or mopping near the front of the unit. Damage
to the grille and/or switch can occur.

3. Periodically clean the inside of the ice machine

components and inside of unit (see Cleaning
Your Ice Machine section).

4. Periodically check and/or clean the front grille

and condenser coils as needed.

5. If your ice machine has either a stainless steel

door and/or cabinet, to keep it looking its best,
we recommend periodically applying a stain-
less steel cleaner and a non-abrasive stainless
steel polish. This is especially important for
outdoor applications and locations near salt-
water environments.

Normal Responsibilities of the Owner

• All freight charges

• Damage sustained in transit

• Mileage charge(s) for service calls

• Proper installation including installation of level-

ing legs.

• Leveling of unit.

• Alterations to original equipment

• Removal or installation of additional equipment

(i.e. drain pump).

• Cleaning and normal maintenance outlined in

this manual.

• Drain and water supply plumbing to the ice

machine.

Help Prevent Tragedies

Each year, children die because they climb inside
a discarded refrigeration product, get trapped
inside and suffocate.  Take precautions to prevent
such tragedies by removing the door, taping or
chaining it shut before discarding.

Summary of Contents for 30AIM 115V





















Reviews: